Eenvoudig geweven hemdje: bekijk maten, technische tekeningen, broninformatie en beschikbare PDF-bestanden. Technische instructies en bestaande PDF’s zijn in het Engels.
Print op 100% of werkelijke grootte, zonder aanpassen aan de pagina. Meet het controlevak op de gekozen testpagina: 50 mm of 2 inch (50,8 mm). Dit zijn verschillende lengtes. Maak eerst een proefmodel voordat je je definitieve stof knipt.
Wissel tussen centimeters en inches in alle tabellen
Je eigen lichaamsmaten. Meet over onderkleding met een aansluitend meetlint.
Maten van het genaaide kledingstuk, inclusief de bedoelde bewegingsruimte.
Select your size primarily based on your high bust measurement if you have a full bust cup (C cup and above), or your full bust measurement if you have an A/B cup. The tank provides 8–9 cm (3.1–3.5") of positive bust ease. If you measure between sizes, we recommend choosing the smaller size for a neater shoulder fit, or blending between bust and hip sizes following our guide.
Positive ease built into this pattern: +8 to +9 cm (+3.1" to +3.5") at bust, and +10 to +12 cm (+4" to +4.7") at hem sweep. Designed to float effortlessly over the torso without clinging or gaping.
Lightweight to medium-weight woven fabrics · None (0% stretch – stable woven)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.2 | 1.3 | 0.9 | 1 |
| L – XL | 1.4 | 1.5 | 1.1 | 1.2 |
| 2XL – 3XL | 1.7 | 1.9 | 1.4 | 1.5 |
1.5 cm (5/8") included on all shoulder and side seams.
1.5 cm (5/8") total hem allowance, sewn as a double-turned baby hem (press up 6 mm, then fold 9 mm and edgestitch).
6 mm (1/4") allowance designed specifically for clean-finish bias binding application.
Pre-wash and dry your fabric exactly as you intend to care for the finished garment to eliminate residual shrinkage.
Press the fabric completely flat before laying out pattern pieces.
Fold fabric selvage-to-selvage on the straight of grain. Test grainline alignment by measuring from the fold to the selvage at several points.
Cut bias strips at an exact 45-degree angle to the selvage; accurate bias cutting ensures smooth, puckering-free curves.
Before printing pattern tiles, print only Page 1 with scaling set to '100%' or 'Actual Size' in Adobe Acrobat or your PDF reader. Do not select 'Fit to Page'. Measure the printed 50 mm x 50 mm (Metric) or 2.0 in x 2.0 in [50.8 mm] (Imperial) test box with a reliable hard ruler. Proceed with printing only when measurements match exactly.
Trim along the right and bottom border lines indicated by the scissor icon on each page. Butt trimmed edge against the adjacent page's marked registration lines. Match the diamond registration marks (1A, 1B, 2A, etc.) and secure with clear tape. Never overlap pages without trimming.
Staystitch the front and back neckline and armholes 10 mm (3/8") from the raw edge using a 2.0 mm stitch length. Stitch from the shoulder towards center front, and from shoulder towards the underarm. Staystitching prevents curved woven edges from stretching out of shape during handling.
With right sides together, pin Front Bodice to Back Bodice along the shoulder seams, matching neck edges and armhole notches. Stitch at 1.5 cm (5/8") seam allowance. Finish the raw seam allowances together with an overlocker/serger, zigzag stitch, or French seam. Press seam allowances toward the back.
Press your 3.5 cm bias strip in half lengthwise with wrong sides together. Pin the raw edges of the folded strip to the right side of the neckline, gently easing the strip around curves (bias tape should be approximately 10–12% shorter than the neckline perimeter). Stitch with a 6 mm (1/4") seam allowance. Grade seam allowance to 3 mm, understitch binding to allowance, then turn binding entirely to the garment inside and edgestitch in place.
In the same manner as the neckline, pin, stitch, understitch, and turn the armhole bias strips to the inside of both armholes. Press crisp and flat with ample steam.
With right sides together, align the front and back side seams, matching underarm seam junctions and hem notches. Pin securely. Stitch at 1.5 cm (5/8") from underarm down to the hem notch. Backstitch firmly at the hem slit reinforcement point. Finish allowances separately and press open.
Press up the lower hem edge by 6 mm (1/4") toward the wrong side. Fold up a second time by 9 mm (3/8"), encasing raw edges. Pin in place. From the inside, edgestitch the hem 1 mm from the inner folded edge. Give the entire garment a final thorough steam press.
Bias binding was stretched during sewing or cut too long relative to the neckline opening.
Unpick the binding, gently steam-shrink the garment neckline with an iron, and shorten the bias strip by 2–3 cm so it stretches gently around the curve when pinned.
High armscye or insufficient armhole depth for your shoulder slope.
Scoop out the underarm curve by 1 cm (3/8") tapering to zero at the mid-armhole notch before applying bias tape.
Fabric was stretched or fed unevenly through standard presser foot.
Loosen presser foot pressure, use a walking foot if available, and use a generous burst of steam with a wooden clapper to set the fold.
In-house digital draft specification created for Threadline Patterns. Released under Creative Commons Attribution 4.0 International (CC BY 4.0). Free for personal and commercial sewing.
CC BY 4.0
https://creativecommons.org/licenses/by/4.0/
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Threadline Pattern Studio
Tops en hemdjes · Beginner
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructiesTops en hemdjes · Beginner
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructiesTops en hemdjes · Gemiddeld
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructies