Breanna aansluitend lijfjesbasispatroon: bekijk maten, technische tekeningen, broninformatie en beschikbare PDF-bestanden. Technische instructies en bestaande PDF’s zijn in het Engels.
Print op 100% of werkelijke grootte, zonder aanpassen aan de pagina. Meet het controlevak op de gekozen testpagina: 50 mm of 2 inch (50,8 mm). Dit zijn verschillende lengtes. Maak eerst een proefmodel voordat je je definitieve stof knipt.
Wissel tussen centimeters en inches in alle tabellen
Je eigen lichaamsmaten. Meet over onderkleding met een aansluitend meetlint.
Maten van het genaaide kledingstuk, inclusief de bedoelde bewegingsruimte.
Select size based on full bust/chest measurement.
+4 to +8 cm positive wearing ease for comfortable drape.
Lightweight to medium-weight suitable fabric substrates · None (0% stable woven)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1 | 1.1 | 0.8 | 0.85 |
| L – XL | 1.2 | 1.3 | 1 | 1.1 |
| 2XL – 3XL | 1.4 | 1.55 | 1.2 | 1.3 |
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
Transfer every front bust dart, front waist dart, and back waist dart from the printed pattern before removing the paper. Fold each dart right sides together, stitch from the wide end to the marked point, and secure the point without backstitching. Press bust darts downward and waist darts toward center.
Staystitch the front and back neckline and armholes just inside the printed seam line. Place Front Bodice and Back Bodice right sides together, stitch both shoulder seams using the printed allowance, finish the raw edges, and press the seams open.
Join the Neckline Binding Strip ends, fold the strip lengthwise, and press. Pin it to the right side of the neckline without stretching the bodice, stitch, trim and grade the seam allowance, then turn the binding fully inside and edge-stitch.
Baste the Front Bodice and Back Bodice right sides together at the side seams and check the close-fitting block over the intended undergarments. Make equal adjustments on both sides, then stitch permanently, finish the raw edges, and press the seams open.
Join each Armhole Binding Strip into a loop and apply it to one armhole with right sides together. Trim and grade the seam, turn the binding fully to the inside, and edge-stitch. Repeat for the second armhole and compare both sides for symmetry.
Turn the printed hem allowance to the wrong side, clip or ease only where required by the curve, press, and stitch evenly. Give the dart points, bindings, side seams, and hem a final press without flattening the bust shaping.
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
FreeSewing (breanna-fitted-bodice). Distributed under MIT / CC BY 4.0. Designer: Joost De Cock & FreeSewing Community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://github.com/freesewing/freesewingParametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Community Open Source Verification
Tops en hemdjes · Beginner
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructiesTops en hemdjes · Beginner
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructiesTops en hemdjes · Beginner
Maten: XS – 3XL · Gepubliceerd
Bekijk patroon en instructies