シンプルなニットTシャツの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロードすべての表でセンチメートルとインチを切り替えます
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
デザイン上のゆとりを含めた、完成した衣服の寸法です。
Constructed with +4 cm (+1.6") of gentle ease over the full bust for a classic semi-fitted look. If you prefer a tight fit, choose one size smaller than your body measurement. Test your knit fabric stretch on our 10cm ruler guide before cutting.
+4 cm (+1.6") ease at bust for comfortable knit wear without clinging.
Knit fabrics with minimum 20% 2-way or 4-way stretch and good recovery · Minimum 20% horizontal stretch with minimum 80% recovery
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.4 | 1.5 | 1.1 | 1.2 |
| L – XL | 1.7 | 1.9 | 1.3 | 1.4 |
| 2XL – 3XL | 2 | 2.2 | 1.5 | 1.65 |
1.0 cm (3/8") for all stretch seams.
2.5 cm (1") for lower hem and sleeve hems.
6 mm (1/4") for neckband seam allowance.
Do not allow knit fabric to hang over the table edge when cutting, as weight will distort the grain.
Use rotary cutter and weights rather than pins to prevent dragging knit fibers.
Print Page 1 at 100% scale. Verify 5cm/2in test box before printing complete pattern set.
Tape pages sequentially matching coordinate grid markers.
Place clear elastic or twill tape along back shoulder seam inside seam allowance. With right sides together, stitch shoulders using a narrow zigzag (0.5 mm width, 2.5 mm length) or serger at 1.0 cm (3/8"). Press toward back.
Fold neckband strip right sides together matching short ends; stitch at 6 mm to form loop. Press loop wrong sides together lengthwise. Mark quarters on neckband and neckline. Pin matching marks. Stitch neckband to neckline stretching ONLY the band, not the garment neckline. Press seam allowance down and steam thoroughly.
With bodice open flat right side up, align sleeve cap to armscye right sides together. Match center notch to shoulder seam. Stitch at 1.0 cm (3/8") and press toward sleeve.
Pin from sleeve hem down through underarm to body hem. Stitch in one continuous seam at 1.0 cm (3/8"). Press toward back.
Press sleeve hems up 2.5 cm and lower body hem up 2.5 cm. Pin or use fusible wash-away tape. From the right side, topstitch using a twin needle (4.0 mm) or a subtle zigzag stitch. Give final press.
Neckband was cut too long for the fabric's stretch ratio or was not stretched enough during sewing.
Unpick band, shorten by 2–3 cm (standard ratio is 80–85% of neckline perimeter for ribbing), and reinstall with even quarter-stretching.
Knit fabric was stretched as it was fed under presser foot.
Loosen presser foot pressure, use wash-away hem tape to stabilize the edge, and press heavily with steam.
In-house digital draft specification created for Threadline Patterns. Released under Creative Commons Attribution 4.0 International (CC BY 4.0). Free for personal and commercial sewing.
CC BY 4.0
https://creativecommons.org/licenses/by/4.0/
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Astrid Lindholm