Breanna フィットした身頃の基本型の寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロードすべての表でセンチメートルとインチを切り替えます
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
デザイン上のゆとりを含めた、完成した衣服の寸法です。
Select size based on full bust/chest measurement.
+4 to +8 cm positive wearing ease for comfortable drape.
Lightweight to medium-weight suitable fabric substrates · None (0% stable woven)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1 | 1.1 | 0.8 | 0.85 |
| L – XL | 1.2 | 1.3 | 1 | 1.1 |
| 2XL – 3XL | 1.4 | 1.55 | 1.2 | 1.3 |
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
Transfer every front bust dart, front waist dart, and back waist dart from the printed pattern before removing the paper. Fold each dart right sides together, stitch from the wide end to the marked point, and secure the point without backstitching. Press bust darts downward and waist darts toward center.
Staystitch the front and back neckline and armholes just inside the printed seam line. Place Front Bodice and Back Bodice right sides together, stitch both shoulder seams using the printed allowance, finish the raw edges, and press the seams open.
Join the Neckline Binding Strip ends, fold the strip lengthwise, and press. Pin it to the right side of the neckline without stretching the bodice, stitch, trim and grade the seam allowance, then turn the binding fully inside and edge-stitch.
Baste the Front Bodice and Back Bodice right sides together at the side seams and check the close-fitting block over the intended undergarments. Make equal adjustments on both sides, then stitch permanently, finish the raw edges, and press the seams open.
Join each Armhole Binding Strip into a loop and apply it to one armhole with right sides together. Trim and grade the seam, turn the binding fully to the inside, and edge-stitch. Repeat for the second armhole and compare both sides for symmetry.
Turn the printed hem allowance to the wrong side, clip or ease only where required by the curve, press, and stitch evenly. Give the dart points, bindings, side seams, and hem a final press without flattening the bust shaping.
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
FreeSewing (breanna-fitted-bodice). Distributed under MIT / CC BY 4.0. Designer: Joost De Cock & FreeSewing Community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://github.com/freesewing/freesewingParametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Community Open Source Verification