Hugo カンガルーポケット付きパーカーの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロードすべての表でセンチメートルとインチを切り替えます
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
デザイン上のゆとりを含めた、完成した衣服の寸法です。
Select by chest measurement. Hugo is drafted for relaxed layering; compare the finished chest and length before cutting.
+18 cm positive ease at the chest in this fixed-size review adaptation.
French terry, sweatshirt fleece, or heavy cotton jersey · 20-40% Stretch
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 2.2 | 2.4 | 1.8 | 1.95 |
| L – XL | 2.6 | 2.85 | 2.1 | 2.3 |
| 2XL – 3XL | 3 | 3.3 | 2.5 | 2.75 |
10 mm (3/8 in) included on all seams.
10 mm (3/8 in) seam allowance included for attaching the rib waistband.
10 mm (3/8 in) included at hood, neck-binding and raglan seams.
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
Stabilize the marked ends of both diagonal hand openings, turn the opening allowances to the wrong side, and topstitch them. Press the remaining Kangaroo Pocket edges under, align its center fold and placement marks with the Hoodie Front Body, then topstitch the sides and lower edge with reinforced stitching at all four opening ends.
Match each Raglan Sleeve to the front body at the single-notch seam and to the back body at the double-notch seam, right sides together. Stitch all four raglan seams with a stretch-compatible stitch, finish the allowances together, and press them toward the sleeves.
Fold the hoodie right sides together and match the raglan seam intersections. Stitch continuously from each sleeve wrist through the underarm and down the body side seam. Finish the allowances together and press them toward the back.
Stitch the shell hood center-back seam and repeat for the lining. Place shell and lining right sides together, stitch the face opening, turn and press, then topstitch the marked drawcord casing. Work the drawcord through the casing before attaching the hood.
Overlap the crossover hood fronts at the center-front notch and baste the overlap. Match the hood center back to the body center back, pin the hood to the neckline right sides together, stitch, and cover the finished seam allowance with herringbone twill tape.
Join the Rib Wrist Cuffs and Rib Hem Waistband into separate loops, then fold each loop lengthwise wrong sides together. Quarter-mark every band and opening; stretch the rib evenly while attaching the cuffs and waistband with a stretch-compatible stitch.
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
Adapted from FreeSewing Hugo documentation and source, distributed under the upstream MIT license. Original design by Joost De Cock and the FreeSewing community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://freesewing.eu/docs/designs/hugo/Parametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Threadline review pending