1
Shoulder Seams
Stabilize shoulder seams and stitch front and back body panels right sides together using a stretch stitch. Press seams open or toward back.
ハーフジップのフリースプルオーバー – 型紙一覧
ハーフジップのフリースプルオーバーの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 中級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on chest measurement. For an oversized streetwear fit, choose one size up.
ゆとりについて
+12 to +18 cm chest ease for athletic mid-layer pullover fit.
生地と用具
Polar fleece, microfleece, or sherpa fleece (220–320 gsm) · 15–30% crosswise stretch
- Polartec or anti-pill polyester fleece (250 gsm)
- Microfleece or grid fleece
- Heavy loopback French terry
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.9 | 2.1 | 1.5 | 1.65 |
| L – XL | 2.2 | 2.4 | 1.8 | 1.95 |
| 2XL – 3XL | 2.6 | 2.85 | 2.1 | 2.3 |
Notions
- Matching polyester all-purpose thread
- Ballpoint or jersey needle (size 80/12 or 90/14)
- 20–25 cm (8–10 in) nylon coil separating or sport zipper
- Fusible knit stay tape for zipper opening
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Pullover Front Body: Cut 1 on Fold in Fleece Half-zip center front
- Pullover Back Body: Cut 1 on Fold in Fleece Fleece back
- Sleeves: Cut 1 Pair in Fleece Set-in sleeves
- Stand Collar: Cut 2 in Fleece (1 Inner, 1 Outer) Stand collar
- Sleeve Cuffs: Cut 1 Pair in Fleece Fleece wrist cuffs
- Bottom Hem Band: Cut 1 on Fold in Fleece Fleece hem band
- Zipper Guard: Cut 1 in Fleece Chin guard
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Assemble Stand Collar & Zipper Guard
Stitch outer collar to body neckline right sides together. Fold zipper guard lengthwise and press. Pin zipper face-down along front slit opening with zipper guard behind left tape.
3
Install Half-Zip
Stitch zipper tape into front opening using a zipper foot. Fold inner collar down over zipper tape to encase top teeth cleanly and topstitch zipper edges.
4
Set Sleeves Flat & Stitch Side Seams
Pin sleeve caps into armholes and stitch. Pin front and back together at side seams, matching underarms, and sew continuously from sleeve hem to lower edge.
5
Attach Cuffs and Hem Band
Form cuff and hem band pieces into loops, fold wrong sides together, and serge to sleeve openings and pullover lower edge, stretching evenly.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (half-zip-fleece-pullover). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification