1
Interface and Construct Visor Peak
Insert rigid Peltex/interfacing between upper and lower visor pieces right sides together. Stitch outer curved edge at 6 mm, trim seam allowance, turn right side out, press, and topstitch outer rim.
Florent ハンチング帽 – 型紙一覧
Florent ハンチング帽の寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- S – 2XL (Head 54–62 cm)
- 難易度
- 中級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on measured head circumference above the eyebrows.
ゆとりについて
+1.5 cm head ease for all-day comfort.
生地と用具
Cotton canvas, denim, wool tweed, or linen · None (0% stable woven)
- Cotton canvas, denim, wool tweed, or linen
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| S – M | 0.5 | 0.55 | 0.4 | 0.45 |
| L – 2XL | 0.6 | 0.65 | 0.5 | 0.55 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- Heavy-duty thread
- Firm fusible craft interfacing
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Flat Cap Side Crown: Cut 1 Pair in Tweed, 1 Pair in Lining Curved side crown panels
- Center Crown Strip: Cut 1 on Fold in Tweed, 1 on Fold in Lining Graded center top crown panel
- Flat Cap Visor Peak: Cut 2 in Tweed, 1 in Rigid Peltex Curved visor peak with firm insert
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Assemble Main Crown
Stitch curved center crown strip between left and right side crown panels right sides together, matching balance notches. Press seams open over a tailor's ham.
3
Assemble Crown Lining
Repeat crown assembly for lining pieces, pressing seams open neatly.
4
Attach Visor to Crown
Align center mark of finished visor peak with center front seam of outer crown. Baste securely within the seam allowance.
5
Enclose Lining & Finish with Sweatband
Join outer crown and lining around lower edge, encasing the visor seam. Turn right side out, press perimeter, and topstitch internal grosgrain sweatband ribbon into place.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
FreeSewing (florent-flat-cap). Distributed under MIT / CC BY 4.0. Designer: Joost De Cock & FreeSewing Community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://github.com/freesewing/freesewing検証について
Parametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Community Open Source Verification