1
Construct Neck Ties
Fold neck tie strips lengthwise right sides together. Stitch along long edge and one short end, trim corner, turn right side out using a loop turner, and press crisp.
布帛のサマーホルタートップス – 型紙一覧
布帛のサマーホルタートップスの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初心者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on full bust/chest measurement.
ゆとりについて
+4 to +8 cm positive wearing ease for comfortable drape.
生地と用具
Lightweight to medium-weight woven fabric: linen, cotton lawn, rayon challis, or chambray · None (0% stable woven)
- 100% washed linen (150–180 gsm)
- Cotton lawn or batiste
- Viscose / rayon challis
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 0.9 | 1 | 0.8 | 0.85 |
| L – XL | 1.1 | 1.2 | 0.9 | 1 |
| 2XL – 3XL | 1.3 | 1.4 | 1.1 | 1.2 |
Notions
- Matching all-purpose thread
- Universal needle (size 70/10 or 80/12)
- 25 mm (1 in) knit elastic for back band
- Lightweight fusible interfacing for facing set
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Halter Front Bodice: Cut 1 on Fold in Fabric Diagonal halter neckline
- Halter Back Band: Cut 1 on Fold in Fabric Elastic casing band
- Neck Ties: Cut 1 Pair in Fabric Tie straps
- Front Halter Facing: Cut 1 on Fold + Interfacing Clean finish halter neck
- Back Band Facing: Cut 1 on Fold + Interfacing Clean finish back band
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Prepare Facing & Baste Ties
Fuse interfacing to front and back facing pieces. Baste the raw ends of the finished neck ties to the upper neck peaks of the front bodice facing toward center.
3
Attach Facing & Encase Neckline
Pin front facing to front bodice right sides together, sandwiching the neck ties. Stitch upper halter neckline and curved underarm edges. Clip curves, turn right side out, and understitch facing.
4
Construct Elasticated Back Band
Stitch back band into a casing channel. Thread 25 mm elastic through, distribute gathers evenly, and secure elastic ends with vertical staystitches.
5
Side Seams & Curved Hem
Join front bodice and elasticated back band at side seams right sides together, enclosing facing raw edges. Press seams open. Turn narrow double-fold hem along bottom edge and topstitch.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (woven-summer-halter-top). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification