1
Join Shoulder Seams
Place the fitted Front Body and Back Body right sides together, match the shoulder edges, and stitch with a stretch-compatible stitch or serger. Finish the allowances together and press them toward the back.
Teagan スクープネックTシャツ – 型紙一覧
Teagan スクープネックTシャツの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初心者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on full bust/chest measurement.
ゆとりについて
+4 to +8 cm positive wearing ease for comfortable drape.
生地と用具
Cotton-spandex jersey knit (180–220 gsm) · 30–40% crosswise stretch with minimum 80% recovery
- Cotton-spandex jersey knit with 4-way stretch
- Bamboo jersey knit with 5% elastane
- Modal stretch jersey
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.3 | 1.4 | 1.1 | 1.2 |
| L – XL | 1.5 | 1.65 | 1.3 | 1.4 |
| 2XL – 3XL | 1.8 | 1.95 | 1.5 | 1.65 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
20 mm sleeve and body hem with twin needle or coverstitch.
6 mm (1/4 in) for neckband or binding attachment.
- Front Body: Cut 1 on Fold Scoop neckline front body
- Back Body: Cut 1 on Fold High back neckline
- Short Sleeve: Cut 1 Pair Set-in short sleeves
- Rib Neckband: Cut 1 Folded rib or self neckband
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Prepare the Scoop Neckband
Stitch the short ends of the Rib Neckband right sides together to form a loop, press the seam open, and fold the loop lengthwise wrong sides together. Quarter-mark the band and scoop neckline, then stitch the band to the neckline with even stretch so the deep curve lies flat without gathers.
3
Insert Sleeves Flat into the Scoop-Neck Tee
With right sides together, match each Short Sleeve center cap notch to the shoulder seam and match the front and back notches. Ease only the sleeve cap between notches and stitch each sleeve into the armhole flat.
4
Shape the Fitted Side Seams
Fold the tee right sides together and match the underarm intersections. Stitch continuously from each sleeve hem through the underarm and along the shaped body side seam to the hem. Finish the allowances together and press toward the back.
5
Finish the Sleeve and Body Hems
Try on the fitted tee and check that the scoop neckline sits flat. Press the sleeve and body hem allowances to the wrong side and topstitch with a twin needle, coverstitch, or narrow zig-zag without stretching the fabric.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
FreeSewing (teagan-fitted-tshirt). Distributed under MIT / CC BY 4.0. Designer: Joost De Cock & FreeSewing Community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://github.com/freesewing/freesewing検証について
Parametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Community Open Source Verification