1
Interface the Shirt Components
Apply lightweight fusible interfacing to one Collar Leaf, one Collar Stand, the outer Sleeve Cuffs, and the marked front placket areas. Let every fused piece cool flat before handling.
Simon メンズシャツ – 型紙一覧
Simon メンズシャツの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 中級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size corresponding to full chest/bust measurement. Compare bicep circumference for comfortable sleeve fit.
ゆとりについて
Tailored shirts incorporate +10 to +14 cm chest ease for relaxed everyday movement and layering.
生地と用具
Cotton poplin, Oxford cloth, linen, or chambray · None (0% stable woven)
- Cotton poplin, Oxford cloth, linen, or chambray
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 2 | 2.2 | 1.6 | 1.75 |
| L – XL | 2.3 | 2.5 | 1.9 | 2.1 |
| 2XL – 3XL | 2.7 | 2.95 | 2.2 | 2.4 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 10 to 12 mm shirt buttons (8 to 10 count)
- Lightweight fusible interfacing for collar and cuffs
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
10 mm (3/8 in) for collar stand seam.
- Shirt Front with Placket: Cut 1 Pair (Left & Right) 10mm seams, 30mm placket
- Shirt Back Bodice: Cut 1 on Fold Box pleat at yoke
- Back Yoke: Cut 2 on Fold (1 Outer, 1 Facing) Burrito method yoke
- Shirt Sleeve: Cut 1 Pair Set-in sleeve with pleats
- Collar Leaf: Cut 2 (1 Interfaced) 6mm seams
- Collar Stand: Cut 2 (1 Interfaced) 6mm seams
- Sleeve Cuffs: Cut 2 Pairs (1 Interfaced) Button cuffs
- Sleeve Plackets: Cut 2 in Main Tower plackets
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Form the Front Button Plackets
Fold the integrated placket extensions on both Shirt Front pieces along the printed fold lines. Press the turns sharply, confirm that the finished fronts mirror one another, and edge-stitch the inner folded edges.
3
Pleat the Back and Attach the Yokes
Fold and baste the marked box pleat in the Shirt Back Bodice. Sandwich its upper edge between the outer and inner Back Yoke pieces right sides together, stitch, turn the yokes upward, and press the enclosed seam.
4
Join the Front Shoulder Seams
Pin each Shirt Front shoulder to the outer Back Yoke right sides together and stitch the shoulder seams. Roll the shirt body for the burrito method, wrap the inner yoke over each shoulder seam, stitch again along the same seam line, turn the shirt right side out, and press.
5
Construct and Attach the Collar
Stitch the Collar Leaf pieces right sides together, trim the corners, turn, press, and topstitch. Baste the collar between the Collar Stand pieces, sew the stand around the collar, then attach the outer stand to the shirt neckline. Turn under the inner stand edge and edge-stitch it closed.
6
Sew the Tower Sleeve Plackets
Transfer the sleeve slash and pleat marks. Apply each Sleeve Placket to its Shirt Sleeve, slash to the marked point, turn the placket through, fold the tower, and edge-stitch around it. Reinforce the top of the slash and baste the wrist pleats.
7
Set the Shirt Sleeves
With right sides together, match each Shirt Sleeve center cap notch to the shoulder seam and match the front and back armhole notches. Ease the cap between notches, stitch the sleeve into the closed armhole, finish the seam, and press the allowance toward the sleeve.
8
Close the Shirt and Sleeve Seams
Match the front and back right sides together and align the underarm intersections. Stitch each side seam and sleeve underarm seam continuously from the shirt-tail hem to the sleeve wrist. Finish the allowances and press them toward the back.
9
Attach the Button Cuffs
Fold each interfaced and non-interfaced Sleeve Cuff right sides together, stitch the short ends, trim, turn, and press. Attach the outer cuff to the pleated sleeve wrist, turn under the inner cuff edge, and edge-stitch it closed.
10
Hem and Add Shirt Buttons
Turn and stitch a narrow double-fold hem around the curved shirt-tail. Mark the center-front, collar-stand, and cuff closures from the pattern; sew buttonholes on the designated overlap side and attach the corresponding buttons on the underlap side.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
FreeSewing (simon-tailored-shirt). Distributed under MIT / CC BY 4.0. Designer: Joost De Cock & FreeSewing Community.
MIT / CC BY 4.0 Joost De Cock & FreeSewing Community
https://github.com/freesewing/freesewing検証について
Parametric drafting geometry, seam balance, and grading verified with upstream open source community testing.
community-tested · verified
Joost De Cock & FreeSewing Community · Community Open Source Verification