ゆったりした布帛トップスの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロードすべての表でセンチメートルとインチを切り替えます
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
デザイン上のゆとりを含めた、完成した衣服の寸法です。
This design features intentional oversized ease (+16 cm / 6.3" at bust). Check the finished garment measurements to select your preferred silhouette: choose your standard size for a fashionable relaxed boxy look, or size down one size for a more tailored profile.
+16 cm to +17 cm (+6.3" to +6.7") ease throughout bust and chest; straight-cut profile with side vent openings for clean draping over high-waisted trousers.
Medium-weight woven fabrics with body and drape · None (0% stretch)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.4 | 1.5 | 1.1 | 1.2 |
| L – XL | 1.7 | 1.9 | 1.3 | 1.4 |
| 2XL – 3XL | 2 | 2.2 | 1.6 | 1.75 |
1.5 cm (5/8") for shoulder and side seams.
3.0 cm (1 1/4") for body hem and 2.5 cm (1") for sleeve cuff hems.
1.0 cm (3/8") for neck facing seam allowance.
Ensure grainline runs vertical down center front and center back folds.
Fuse interfacing to facings using a dry press cloth before cutting out curved facing pieces to avoid distortion.
Clip small 3 mm notches into the sleeve cuff hem lines.
Print Page 1 at 100% scale (no scaling / actual size). Measure test calibration square before printing complete packet.
Align numbered grid borders and diamond registration pins. Tape sheets together without overlapping uncut paper.
Apply fusible interfacing to the wrong sides of Front and Back Neck Facings. With right sides together, stitch facings at shoulder seams using 1.0 cm (3/8") seam allowance. Press seams open. Finish outer raw edge of facing with serger or small turned-and-stitched edge.
With right sides together, pin Front and Back Bodice along continuous shoulder and upper sleeve seams. Stitch at 1.5 cm (5/8"). Finish allowances and press toward back.
Pin facing to garment neckline right sides together, aligning shoulder seams and center notches. Stitch at 1.0 cm (3/8"). Clip curves at 1.5 cm intervals. Press seam allowances toward facing, then understitch facing 2 mm from seam. Turn facing inside and press flat.
Pin side seams from underarm down to side vent notch. Stitch at 1.5 cm (5/8"). Backstitch securely at vent notch. Press side seam and vent extensions open.
Turn sleeve hems under 1 cm, then 1.5 cm; press and edgestitch. Turn lower hem under 1.5 cm, then 1.5 cm; stitch continuous hem across vents and hemline.
Understitching was skipped or facing wasn't secured to shoulder allowances.
Tack the facing to the shoulder seam allowances with small hand stitches or machine stitch in the ditch.
Underarm curve seam is too shallow for your reach.
Reinforce underarm with small stay-stitches, then clip underarm curve every 1 cm to release tension.
In-house digital draft specification created for Threadline Patterns. Released under Creative Commons Attribution 4.0 International (CC BY 4.0). Free for personal and commercial sewing.
CC BY 4.0
https://creativecommons.org/licenses/by/4.0/
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Astrid Lindholm