1
Prepare Patch Pockets
Fold pocket top hem to right side, stitch side seam allowances, turn right side out, and press. Topstitch pocket hem, then pin and edgestitch pockets onto cardigan front markings.
パッチポケット付きカーディガン – 型紙一覧
パッチポケット付きカーディガンの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on chest measurement. For an oversized streetwear fit, choose one size up.
ゆとりについて
+12 to +18 cm bust ease for comfortable layering over tees and shirts.
生地と用具
Medium to heavyweight knit: sweater knit, French terry, or ponte roma (240–340 gsm) · 20–35% crosswise stretch with good recovery
- Ribbed or textured sweater knit
- French terry with 25% stretch
- Ponte di Roma knit
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.8 | 1.95 | 1.5 | 1.65 |
| L – XL | 2.1 | 2.3 | 1.7 | 1.85 |
| 2XL – 3XL | 2.4 | 2.6 | 2 | 2.2 |
Notions
- Matching polyester stretch thread
- Ballpoint or stretch machine needle (size 80/12)
- 5 buttons (20–25 mm)
- Fusible knit stay tape for front button placket
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Cardigan Front: Cut 1 Pair V-neck cardigan front panels
- Cardigan Back: Cut 1 on Fold Cut on center back fold
- Sleeves: Cut 1 Pair Full-length set-in sleeves
- Front Placket Band: Cut 2 (or 1 Long Continuous Band on Fold) Continuous neck and front placket band
- Patch Pockets: Cut 1 Pair in Self Knit Front waist patch pockets
- Rib Wrist Cuffs: Cut 1 Pair in Ribbing or Self Folded knit wrist cuffs
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Shoulder & Neckline Staystitching
Stabilize shoulder seams with clear elastic or knit stay tape. Stitch front and back bodice panels right sides together at the shoulders using a stretch stitch or serger.
3
Set Sleeves Flat
Pin sleeve caps right sides together along the open armholes, matching notches and easing fullness evenly. Stitch across each armhole.
4
Side and Underarm Seams
Align front and back pieces right sides together, matching underarm seam intersections. Stitch each side seam and sleeve underarm in one continuous pass.
5
Attach Continuous Front Placket Band
Fold placket band lengthwise wrong sides together. Match center back placket notch to back neck, pin along V-neckline down to hem on both sides, stretching slightly along curves. Stitch and press seam toward body.
6
Attach Cuffs, Hem, and Buttons
Fold wrist cuffs into rings, press in half lengthwise, and serge onto sleeve openings. Double-fold and topstitch bottom hem. Mark button placement and sew buttonholes on right placket, buttons on left.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (knit-pocket-cardigan). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification