1
Finish Boatneck Edge
Apply Neckline Facing Strips to Front Bodice on Fold and Back Bodice on Fold right sides together. Turn under and topstitch with twin needle. Press seam allowances flat.
クラシックなマリニエール – 型紙一覧
クラシックなマリニエールの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on full bust/chest measurement.
ゆとりについて
+4 to +8 cm positive wearing ease for comfortable drape.
生地と用具
Lightweight to medium-weight suitable fabric substrates · None (0% stable woven)
- Lightweight to medium-weight suitable fabric substrates
- Pre-washed natural fibers (cotton, linen, or bamboo)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.6 | 1.75 | 1.3 | 1.4 |
| L – XL | 1.9 | 2.1 | 1.5 | 1.65 |
| 2XL – 3XL | 2.2 | 2.4 | 1.8 | 1.95 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Front Bodice on Fold: Cut 1 on Fold Align horizontal stripe repeats horizontally
- Back Bodice on Fold: Cut 1 on Fold Align horizontal stripe repeats horizontally
- 3/4 Sleeve: Cut 1 Pair Align stripe pattern across armscye notches
- Neckline Facing Strips: Cut 2 Strips Cut on straight grain for boatneck stabilization
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Shoulder Seams
Align Front Bodice on Fold and Back Bodice on Fold right sides together. Stitch short shoulder seams with clear elastic reinforcement. Press seam allowances open.
3
Insert 3/4 Sleeves Flat
Insert 3/4 sleeves flat into armholes right sides together, matching stripes at notches. Stitch with stretch stitch and press seam allowances.
4
Side Seams with Vents & Hem
Align front and back bodices right sides together. Stitch side seams stopping 6 cm above hem for side vents. Press seam allowances. Twin needle hem sleeves, side vents, and bottom edge.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (classic-breton-mariniere). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification