1
Shoulder Seams
Stabilize shoulder seams with knit stay tape. Align front and back sweater bodice right sides together at the shoulders and stitch with a stretch stitch or 4-thread serger.
ボートネックのニットトップス – 型紙一覧
ボートネックのニットトップスの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初心者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on chest measurement. For an oversized streetwear fit, choose one size up.
ゆとりについて
+10 to +16 cm chest ease for relaxed drop-shoulder sweater comfort.
生地と用具
Medium to heavyweight knit: French terry, cotton sweater knit, or ponte (220–300 gsm) · 25–40% crosswise stretch with good recovery
- Cotton sweater knit
- French terry with 30% stretch
- Waffle knit or ponte di Roma
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.6 | 1.75 | 1.3 | 1.4 |
| L – XL | 1.9 | 2.1 | 1.5 | 1.65 |
| 2XL – 3XL | 2.2 | 2.4 | 1.8 | 1.95 |
Notions
- Matching polyester stretch thread
- Ballpoint machine needle (size 80/12)
- Matching rib knit fabric for hem and cuff bands (or self-fabric)
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Sweater Front Bodice: Cut 1 on Fold in Knit Fabric Cut on center front fold
- Sweater Back Bodice: Cut 1 on Fold in Knit Fabric Cut on center back fold
- Long Sleeves: Cut 1 Pair Tapered knit sleeves
- Boatneck Facing / Band: Cut 1 in Self or Ribbing Clean-finish boatneck neckline
- Rib Hem Band: Cut 1 in Ribbing or Self Folded bottom hem band
- Rib Wrist Cuffs: Cut 1 Pair in Ribbing or Self Folded wrist cuffs
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Finish Boatneck Neckline
Fold boatneck band lengthwise wrong sides together. Quarter-mark band and wide neckline. Serge band to neckline edge, stretching slightly to lie completely flat against collarbone.
3
Insert Sleeves Flat
Pin sleeve caps to bodice armholes right sides together, aligning center sleeve notch to shoulder seam. Stitch across each armhole.
4
Side and Underarm Seams
Pin front and back right sides together, aligning underarm seam intersections. Stitch side seams and sleeve inseams in one continuous run from cuff to hem.
5
Attach Wrist Cuffs & Hem Band
Fold cuff and hem band pieces into loops, press in half lengthwise, and serge onto sleeve openings and sweater bottom hem with even stretching.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (boatneck-knit-sweater). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification