1
Construct Sleeve Tabs & Front Placket
Stitch sleeve roll tabs right sides together, turn, press, and topstitch. Apply lightweight interfacing to front neckline notch, stitch placket facing around notch, slash, turn inside, and press crisp.
スリットネックのチュニック – 型紙一覧
スリットネックのチュニックの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size corresponding to full chest/bust measurement. Compare bicep circumference for comfortable sleeve fit.
ゆとりについて
Tailored shirts incorporate +10 to +14 cm chest ease for relaxed everyday movement and layering.
生地と用具
Cotton poplin, Oxford cloth, linen, or chambray · None (0% stable woven)
- Cotton poplin, Oxford cloth, linen, or chambray
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 2.2 | 2.4 | 1.8 | 1.95 |
| L – XL | 2.5 | 2.75 | 2.1 | 2.3 |
| 2XL – 3XL | 2.9 | 3.15 | 2.4 | 2.6 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 10 to 12 mm shirt buttons (8 to 10 count)
- Lightweight fusible interfacing for collar and cuffs
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
10 mm (3/8 in) for collar stand seam.
- Front Tunic with Notch Placket: Cut 1 on Fold in Fabric Notch neckline
- Back Tunic on Fold: Cut 1 on Fold in Fabric Center back fold
- Back Yoke: Cut 2 in Fabric (1 Outer, 1 Lining) Shoulder yoke
- Tunic Sleeve: Cut 1 Pair in Fabric Roll-tab sleeve
- Mandarin Stand Collar: Cut 2 in Fabric (1 Interfaced) Stand collar
- Sleeve Cuffs: Cut 2 in Self Fabric, 2 in Interfacing Button cuffs
- Sleeve Roll Tabs: Cut 2 in Self Fabric Roll tabs
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Assemble Back Yoke
Sandwich the back tunic body between inner and outer back yokes using the burrito method. Topstitch along yoke seam.
3
Shoulder Seams and Mandarin Stand Collar
Attach front shoulders to back yoke assembly. Interface outer collar stand. Assemble collar stand pieces, turn, and stitch to neckline right sides together, sandwiching neck raw edges.
4
Set Sleeves Flat & Stitch Side Seams
Pin sleeves to armholes matching notches and stitch flat. Stitch side seams from sleeve hem down to tunic hem, leaving 10 cm open at bottom for side vents.
5
Finish Hem, Vents & Sleeve Buttons
Turn and topstitch side hem vents and curved tunic hem. Hem sleeve openings with cuff bands, sew button on outside of sleeve, and secure roll tab.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (popover-notch-neck-tunic). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification