1
Cut Pieces & Apply Interfacing
Cut front legs, back legs, waistband casing, and pocket bags from French terry. Fuse small 25 mm interfacing squares on waistband center front for drawstring eyelets.
フレンチテリーのショートパンツ – 型紙一覧
フレンチテリーのショートパンツの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初心者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size corresponding to natural waist and full hip/seat measurements. If between sizes, choose the larger size and adjust side seams.
ゆとりについて
+6 to +10 cm hip ease for comfortable relaxed lounge fit.
生地と用具
French terry, loopback cotton fleece, or modal stretch knit (240–320 gsm) · 15–25% crosswise stretch with moderate recovery
- 100% cotton French terry
- Cotton-modal loopback knit with 5% elastane
- Medium-weight cotton fleece
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1 | 1.1 | 0.8 | 0.85 |
| L – XL | 1.2 | 1.3 | 1 | 1.1 |
| 2XL – 3XL | 1.4 | 1.55 | 1.2 | 1.3 |
Notions
- Matching polyester or poly-blend thread
- Stretch or ballpoint needle (size 80/12)
- 38 mm (1.5 in) non-roll knit elastic
- 1.5 m flat knit drawstring or cotton cord
- Small piece of fusible interfacing for eyelets
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
15 mm (5/8 in) included on outseams, inseams, and crotch curve.
20 mm (3/4 in) hem.
N/A (Trouser garment).
- Shorts Front Leg: Cut 1 Pair French terry relaxed front leg
- Shorts Back Leg: Cut 1 Pair French terry relaxed back leg
- Elastic Waistband Casing: Cut 1 in Rib Knit or Self Elastic and drawstring rib waistband
- Side Slant Pocket: Cut 2 Pairs Slash hip pockets
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Construct Side Slant Pockets
Stitch pocket facing to front leg pocket opening right sides together. Understitch, press inside, and stitch pocket bags together around curved lower edge.
3
Crotch & Inseam Assembly
Stitch front crotch seam and back crotch seam right sides together using a stretch stitch. Align front and back at inseam, matching crotch intersection, and stitch from hem to hem.
4
Side Outseams
Pin front and back legs right sides together along side outseams, encasing pocket edges smoothly. Stitch with serger or stretch stitch from waist to hem and press toward back.
5
Waistband Casing & Leg Hems
Stitch drawstring eyelets or buttonholes on waistband. Form waistband ring, insert elastic and drawstring, and stitch to shorts waistline. Turn and double-needle hem each leg opening.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (french-terry-sweat-shorts). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification