1
Cutting Heavy Canvas
Cut front bib and leg panels, back bib and leg panels, straps, and divided chest pocket from heavy canvas or denim. Press seam allowances.
ワークサロペット – 型紙一覧
ワークサロペットの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 中級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size corresponding to natural waist and full hip/seat measurements. If between sizes, choose the larger size and adjust side seams.
ゆとりについて
Structured trousers include +4 to +6 cm ease at waistband and +8 to +12 cm ease through hip/thigh for sitting comfort.
生地と用具
Cotton twill, chino, denim, linen, or wool suiting · None (0% stable woven)
- Cotton twill, chino, denim, linen, or wool suiting
- Pocketing cotton for pocket bags
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 2.8 | 3.05 | 2.2 | 2.4 |
| L – XL | 3.2 | 3.5 | 2.6 | 2.85 |
| 2XL – 3XL | 3.7 | 4.05 | 3.1 | 3.4 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 7 inch metal or nylon trouser zipper
- Trouser hook and eye or 18mm button
- Interfacing for waistband
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
15 mm (5/8 in) included on outseams, inseams, and crotch curve.
35 mm (1 3/8 in) hem allowance.
N/A (Trouser garment).
- Front Bib & Leg: Cut 2 in Heavy Canvas One-piece front bib extending down to trouser leg
- Back Bib & Leg: Cut 2 in Heavy Canvas One-piece back racer bib extending down to leg
- Adjustable Straps: Cut 2 Straps Reinforced shoulder straps
- Divided Bib Pocket: Cut 1 Pocket Utility divided chest pocket
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Bib Pocket Construction
Hem top of divided bib pocket and topstitch onto front bib with double needle and center divider stitch. Press seam allowances.
3
Center Seams
Sew front center rise seam and back center rise seam using durable flat-felled seams. Press seam allowances.
4
Straps and Side Seams
Fold and topstitch adjustable shoulder straps. Baste straps to top edge of back bib. Sew side seams leaving hip openings. Press seam allowances.
5
Inseam and Hardware
Align pieces right sides together and stitch inseam, hem trouser legs, and install dungaree buckle sliders and buttons. Press seam allowances.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (british-utility-dungarees). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification