1
Cutting and Preparation
Cut bodice front, bodice back, flared skirt panels, short sleeves, and waist tie strips. Press seam allowances.
ティアードスモックワンピース – 型紙一覧
ティアードスモックワンピースの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on high bust and full bust measurement.
ゆとりについて
+6 to +10 cm bust ease; skirt panel flares generously over hips.
生地と用具
Lightweight to medium-weight suitable fabric substrates · None (0% stable woven)
- Lightweight to medium-weight suitable fabric substrates
- Pre-washed natural fibers (cotton, linen, or bamboo)
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 3.6 | 3.95 | 2.9 | 3.15 |
| L – XL | 4.1 | 4.5 | 3.4 | 3.7 |
| 2XL – 3XL | 4.7 | 5.15 | 3.9 | 4.25 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 18 to 22 inch invisible zipper
- Hook and eye closure
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
15 mm (5/8 in) double-fold hem.
6 mm (1/4 in) for neckband or binding attachment.
- Wrap Front Bodice: Cut 1 Pair (1 Left, 1 Right) Extended crossover bodice front
- Back Bodice: Cut 1 on Fold Center back on straight grain
- Flared Wrap Skirt: Cut 2 Front, 1 Back on Fold Gathered flared skirt panels
- Short Sleeve: Cut 1 Pair Short set-in sleeves with sleeve cap ease
- Waist Tie Belt: Cut 2 in Self Fabric Self-fabric waist tie strips
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Bodice Shoulder Seams
Join bodice shoulder seams and finish neckline edges with narrow hem or bias binding. Press seam allowances.
3
Insert Sleeves
Set short sleeves into armholes with right sides facing, easing sleeve cap fullness into armscye. Press seam allowances.
4
Side Seams and Skirt Gathering
Sew side seams from sleeve hem through bodice. Assemble skirt panels and gather waist edge to fit bodice. Press seam allowances.
5
Waistline and Hemming
Attach gathered skirt to bodice waistline, insert waist tie belt at side seam, and hem skirt sweep. Press seam allowances.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (tiered-cottagecore-smock-dress). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification