1
Staystitch & Mark
Staystitch waistline curves at 8 mm. Transfer pocket, fly topstitch, and rear welt pocket markings onto the fabric wrong side using tailor's chalk.
ゆったりしたペインターパンツ – 型紙一覧
ゆったりしたペインターパンツの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 中級者向け
- バージョン
- 1.0.0-published
- 更新日
- 2026-03-09
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size corresponding to natural waist and full hip/seat measurements. If between sizes, choose the larger size and adjust side seams.
ゆとりについて
Structured trousers include +4 to +6 cm ease at waistband and +8 to +12 cm ease through hip/thigh for sitting comfort.
生地と用具
Cotton twill, chino, denim, linen, or wool suiting · None (0% stable woven)
- Cotton twill, chino, denim, linen, or wool suiting
- Pocketing cotton for pocket bags
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 2.3 | 2.5 | 1.8 | 1.95 |
| L – XL | 2.6 | 2.85 | 2.1 | 2.3 |
| 2XL – 3XL | 3 | 3.3 | 2.5 | 2.75 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 7 inch metal or nylon trouser zipper
- Trouser hook and eye or 18mm button
- Interfacing for waistband
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
15 mm (5/8 in) included on outseams, inseams, and crotch curve.
35 mm (1 3/8 in) hem allowance.
N/A (Trouser garment).
- Front Trouser Leg: Cut 1 Pair (1 Left, 1 Right) Straight relaxed leg
- Back Trouser Leg: Cut 1 Pair (1 Left, 1 Right) Seat curve and dart
- Contoured Waistband: Cut 2 in Fabric, 1 in Fusible Interfacing Contoured waistband
- Front Pocket Facing: Cut 1 Pair in Self Fabric Slash pocket
- Front Pocket Bag: Cut 1 Pair in Pocketing/Lining Pocketing fabric
- Fly Facing: Cut 1 in Self + 1 Interfacing Zipper fly
- Fly Shield: Cut 1 in Self Protective fly shield
- Back Welt Pocket Bands: Cut 2 in Self Fabric Utility welt pockets
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Construct Front Slant Pockets
Pin pocket facings to front trouser leg pocket slant edges right sides together. Stitch, trim seam allowance, understitch facing towards pocket bag, and press crisp.
3
Assemble Back Welt Pockets
Interface welt pocket locations on back legs. Position welt strips, stitch parallel welt lines, cut opening, turn welt through, and press rectangular welt lips. Topstitch pocket bags securely.
4
Install Zipper Fly
Attach interfaced fly facing to left center front edge. Stitch zipper tape to right extension, fold protective shield behind zipper, and topstitch classic curved J-stitch.
5
Join Inseams and Outseams
Pin front and back legs right sides together at outseams and inseams. Stitch from hem up to crotch. Press seams open or finish raw edges with a clean serged finish.
6
Stitch Crotch Curve
Insert one trouser leg inside the other right sides together. Align crotch seam and four-way intersection. Stitch from back waistline through fly base, reinforcing stress point with second pass.
7
Attach Contoured Waistband & Belt Loops
Attach belt loops to waist seam. Stitch interfaced outer waistband to trouser waistline. Press seam up, fold waistband over, stitch in the ditch from right side, and bar-tack belt loops.
8
Hem Trouser Legs
Turn up specified 35 mm hem allowance. Blind-stitch or machine-hem trouser leg hem and perform final steam press.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Threadline Open Design Studio (relaxed-painter-pants). Distributed under CC BY-SA 4.0. Designer: Threadline Technical Team.
CC BY-SA 4.0 Threadline Technical Team
https://threadlinepatterns.org検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Community Open Source Verification