1
Stitch Waist Darts
Fold front and back waist darts right sides together. Stitch from waistline tapering to zero at dart points. Press darts towards center.
アシンメトリーなミディスカート – 型紙一覧
アシンメトリーなミディスカートの寸法表、前後の図、出典、利用できるPDFを確認できます。技術説明と既存PDFは英語です。
- サイズ
- XS – 3XL
- 難易度
- 初級者向け
- バージョン
- 1.0.0
- 更新日
- 2026-09-12
- 公開状況
- 公開済み
前後の製図
PDFファイルのダウンロード
「実際のサイズ」または100%で印刷し、用紙に合わせる設定を使わないでください。選んだテスト用紙の50 mmまたは2インチ（50.8 mm）の枠を測ります。この2つは異なる長さです。本番の生地を裁断する前に試作してください。
印刷確認用シートをダウンロード寸法表
寸法の単位
すべての表でセンチメートルとインチを切り替えます
1. 身体寸法表
身体そのものの寸法です。下着の上から、メジャーを身体に沿わせて測ります。
横にスクロール
2. 仕上がり寸法表
デザイン上のゆとりを含めた、完成した衣服の寸法です。
横にスクロール
サイズ選択について
Select size based on natural waist and fullest hip measurement.
ゆとりについて
The finished measurement chart provides approximately 4 cm waist ease and 8 cm hip ease across the listed size range.
生地と用具
Lightweight to medium-weight stable woven fabric with fluid drape · None (0% stable woven)
- Cotton poplin, chambray, linen, rayon challis, or viscose twill
- Pre-washed stable woven fabric with enough drape for the shaped hem
| Size | 45 in / m | 45 in / yd | 60 in / m | 60 in / yd |
|---|---|---|---|---|
| XS – M | 1.9 | 2.1 | 1.5 | 1.65 |
| L – XL | 2.2 | 2.4 | 1.8 | 1.95 |
| 2XL – 3XL | 2.6 | 2.85 | 2.1 | 2.3 |
Notions
- Matching all-purpose polyester or cotton sewing thread
- Universal sewing needle (size 80/12)
- 7 inch invisible zipper
- Hook and eye closure
- Fusible waistband interfacing
Tools
- Sewing machine
- Fabric shears
- Pins or fabric clips
- Steam iron and ironing board
裁断と型紙パーツ
10 mm (3/8 in) included on all seams.
10 mm (3/8 in) narrow hem included along the shaped high-low edge.
N/A (Skirt garment).
- Front Skirt Panel: Cut 1 on Fold Transfer waist darts and asymmetric hem balance marks
- Back Skirt Panels: Cut 1 Pair (Left & Right) Center back zipper seam; no kick pleat or vent
- Waistband Facing: Cut 2 in Fabric, Cut 1 in Interfacing Clean-finish contoured waist facing
Press fabric before cutting to remove packing folds and pre-shrink fibers.
Align piece grainlines strictly parallel to fabric selvages.
Transfer notch markings with small 3 mm snips into the seam allowance margin.
Print Page 1 at 100% scale without page scaling. Check Metric box (50 mm x 50 mm) or Imperial box (2.0 in x 2.0 in = 50.8 mm) with a rigid ruler.
Align numbered registration marks and butt tile edges flush without overlapping untrimmed paper. Tape securely.
縫製手順
2
Insert Center Back Zipper
Finish the center-back raw edges. Install the 18 cm (7 in) invisible zipper from the waistline, then stitch the remaining center-back seam below the zipper stop.
3
Stabilize the Shaped Hem
Staystitch the curved high-low hem just inside the 10 mm allowance without stretching. Clip only where needed so the narrow hem can turn smoothly.
4
Stitch Side Seams
Pin front to back right sides together, matching waist, hip, and high-hem balance marks. Stitch side seams, finish the raw edges, and press seams open.
5
Attach Waist Facing & Hem
Interface the waist facing, stitch it to the upper edge, understitch, and turn inside. Turn the shaped hem 5 mm twice, easing rather than stretching the curves, then edgestitch.
困ったときは
Seams puckering along stitch line
Thread tension too high or needle blunt
Insert fresh needle and test balance on fabric scrap.
Wavy edge along curved perimeter
Edge was stretched while feeding into machine
Staystitch immediately after cutting and use walking foot.
出典とライセンス
Original in-house pattern created for Threadline Patterns. Released under Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0).
CC BY-SA 4.0 Threadline Technical Team
https://freesewingpattern.com/patterns/asymmetric-midi-skirt/検証について
Prepared from the listed source record through a technical drafting workflow. Check the measurements, print calibration and construction details carefully, and email feedback if anything appears incorrect.
sample-pending · verified
Threadline Technical Team · Threadline Digital Pattern Review